1 5

Flexi Plate with Textured ULTEM PEI - Creality Ender 3 - 235 x 235

$29.00 USD
$29.00 USD $43.00 USD
Sale Sold out
Shipping calculated at checkout.

Product Details

Collapsible Sections with Rounded Corners

Fits: Creality Ender 3 and Elegoo Neptune Series

(Please see full printer list below on the 'Fits & Contents' tab)

Our Textured PEI Flexi Plates start with our premium 0.4mm high chromium spring steel, electrostatically powder painted with authentic ULTEM™ brand PEI from Sabic, and kiln-baked for exceptional durability. The Flexi Plate has a double-sided texture leaving a pronounced finish on the bottom of your print.

Compatible with the Wham Bam Magnetic Base (not included), this Flexi Plate is ideal for a variety of filaments, including PLA, TPU, PETG, and ABS. For additional adhesion with challenging materials like Nylon, use purple glue sticks or Magigoo, which wash off easily.

Please note, this discontinued version does not have alignment notches.

Printer Fits:
• AnkerMake M5C
• BIQU B1
• BIQU Hurakan
• Creality CR-20
• Creality Ender 3
• Creality Ender 3 Neo
• Creality Ender 3 Pro
• Creality Ender 3 S1
• Creality Ender 3 S1 Pro
• Creality Ender 3 V2
• Creality Ender-3 V2 Neo
• Creality Ender 5
• Creality Ender 5 Pro
• Elegoo Neptune 2
• Elegoo Neptune 2D
• Elegoo Neptune 2S
• Elegoo Neptune 3
• Elegoo Neptune 3 Pro
• Elegoo Neptune 4
• Elegoo Neptune 4 Pro
• Elegoo Neptune X
• FOKOOS Odin-5 F3
• JGmaker Magic
• Sovol SV06
• Tevo Tarantula
• TwoTrees Saphire Pro
• Voxelab Aquila

May Fit:
• Anycubic Kobra
• Anycubic Mega Zero 2.0
• Artillery Genius Pro
• Tevo Up Flash

Do you have a printer similar to what's listed under Printer Fits or May Fit?
If you have a printer similar to the one described above and believe our solution could work for your printer, please follow our easy instructions on measuring your build plate. Let us know if your printer matches our specifications or is even close! We’d love to hear about it, and you might even receive a discount on Wham Bam® merchandise for your efforts. Click here for more info.

Measure Your Build Plate

Includes:
  • 1 Powder Painted Ultem™ PEI Flexi Plate
Dimensions:
  • 235 x 235 mm
  • Flexi Plate 0.4 mm
  • ULTEM™ PEI Build Surface 0.12 mm, on each side

Note: You should already have a magnet or clips installed on your printer, as this is needed to use a Flexi Plate.

If your machine has automatic bed leveling, run the leveling process and set your gap such that the first layer is well squished. For more details on achieving the right first layer squish, refer to this bed leveling guide.

If your printer uses manual leveling, follow the same guide for instructions on the leveling process.

Powder Painted Ultem™ PEI Best Practice Use:

Cleaning Before & After prints
After every print, we suggest wiping with isopropyl alcohol and a fresh paper towel. If you have small bits, such as purge lines, stuck to the surface you can try with a steel spatula with corners rounded to carefully remove these. Do not use Acetone as this will damage the surface.


Longterm Contaminants cleaning:
Should the PEI ever lose its grip, you may also try common dish detergent or vinegar and clean with water as these help break fats added to filaments with effects. You can also lightly pass over the plate with 600 grit wet dry sandpaper to revitalize, then clean with IPA and a fresh paper towel.

Table Top / Wall Mount Flexi Plate Holder

Full support info can be found on our support page.

Customer Reviews

Based on 2 reviews
50%
(1)
0%
(0)
50%
(1)
0%
(0)
0%
(0)
E
Eric
Great build plate

I had a cheaper flexible plate with textured surface, and struggled to work with it. The powder coat was uneven, had some sharp little points here and there in the coating, and I think one side was coated thicker than the other so my leveling was tricky. This flexible build plate has been excellent right out of the gate. I get good adhesion and the texture is nice on the bottoms of my prints. I've yet to have a bad experience with WB flexible build plates and will happily buy another if needed.

b
beau leduc

lol. you couldn’t have picked a worse time to hit me up for a review… all of a sudden, i can’t get the filament to stick to save my life on my ender 3 s1 (klipper firmware).

We are sorry to hear you are having this issue. No problem, please reach out to our technical support team at technical@whambamsystems.com and they can help!